Draw a heat loss plan with an AI assistant
An AI assistant working in your browser can draw the plan from your drawings and product list, fill in each room, place the radiators, fan coils and heat pump, lay the pipework and read the results. It uses the same functions you do. Here is what it can do, how it connects, and what stays with you.
In short: HeatLoss Pro offers its tools to AI assistants in two ways: through WebMCP, the W3C community draft for a web page's own tools, where the browser supports it, and as window.HeatLossPro for assistants that run JavaScript in the page. llms.txt describes every tool. Each tool call is one step you can undo, and the assistant can never pay or calculate for you.
What an assistant can do
- Read the plan as it is, with the id of every room, wall, window, emitter and pipe (
get_plan), and the values the tools accept: wall build-ups with their U-values, glazing, shading, room types (get_options). - Draw the outside walls and the inner walls, windows, doors and doorways, and add floors (
draw_walls,add_window,add_floor). Closed walls make the rooms by themselves, as when you draw them. - Fill in each wall, window and room: build-up, glazing, shading, how much of a window opens, room type and temperature, ceiling, underfloor heating, and patios or unheated garages left out of the heated house (
set_wall,set_room), and the house's design temperatures (set_house). - Place the heating: radiators, fan coils and air conditioners from their datasheet figures (
add_emitter), and a heat pump from the catalogue of more than 13,000 models (find_models,add_heat_source). - Lay the pipework in one step (
connect_heating): a manifold in a utility room or hall, one flow and return run through the doorways to every emitter, a mixing valve for underfloor loops when the water is too warm for a floor, and floor links between storeys. - Read the results: each room's heat loss, what its emitters give, the heat pump size and the cooling (
calculate,get_results).
How it connects
Where the browser supports WebMCP (navigator.modelContext), the page registers its tools when the designer opens, and an assistant calls them by name. An assistant that runs JavaScript in the page uses the same tools directly:
window.HeatLossPro.tools()await window.HeatLossPro.call('draw_walls', { points: [[0, 0], [8, 0], [8, 5], [0, 5]], closed: true })Each call resolves to { ok: true, result } or { ok: false, error }; a wrong input says what to change, and changes nothing.llms.txt tells an assistant the tools, the units (metres, x to the right and y down, °C, kW) and the order that works. An assistant that cannot open the page can write a whole plan as JSON in the format it describes; you drop the file on the drawing to open it.
A session, step by step
- The assistant reads the plan. A first visit opens the demo house: it starts a blank plan, after asking you.
- It sets the house: the design temperatures of where it stands, the flow temperature, the cooling water if it cools.
- It draws the outside walls with their build-up, then the inner walls, the doorways between rooms and every window.
- It names each room and sets its type, ceiling and underfloor heating, and marks a patio or covered terrace as outdoors.
- It places each radiator or fan coil with its datasheet figures, and the heat pump from the catalogue.
- It lays the pipework and checks that every emitter is connected.
- It asks for a calculation: you go ahead in the window that opens, and it compares what each emitter gives with what each room needs.
What stays with you
- Every tool call is one step on the Undo button, and is saved like any edit of yours.
- Replacing your drawing, with a blank plan or an imported one, asks you first.
- A calculation that needs payment opens the window where you decide: the assistant can ask, never pay or confirm.
- A shared plan opened to look at stays read only.
- The figures are yours to check: the assistant should tell you which it assumed and which product figures it looked up.
What it does not do
- HeatLoss Pro does not read walls off a PDF or an image for the assistant: the assistant reads your drawings and enters what it reads.
- The pipework it lays is a sound starting layout, sized automatically; you can redraw any run along the walls.
- It does not add emitters by itself: rooms with nothing to heat them are listed, for you or the assistant to decide.
Every step of the calculation itself is in How HeatLoss Pro calculates heat loss. Drawing is free; a calculation with the full report costs €1.
Frequently asked questions
Which AI assistants can use HeatLoss Pro?
Any assistant that works in your browser and either uses the tools a page offers through WebMCP, or runs JavaScript in the page (a browser agent). An assistant that cannot open a web page can still read llms.txt and write a plan file for you to drop on the drawing.
Can the assistant pay for a calculation or see my account?
No. The tools only read and change the plan. A calculation that needs payment opens the window where you decide, and none of the tools reads your account or payment details.
Can I undo what the assistant did?
Yes. Each tool call is one step, so Undo takes back a whole wall outline, a room or the pipework it laid in one go. Replacing your drawing with a new or imported plan asks you first.
Does it read my floor plan from a PDF or an image?
HeatLoss Pro does not read plans for the assistant: the assistant reads your drawings, as it would for you, and enters the walls, windows and rooms it reads. Check the figures it assumed, and the products it looked up.
What does it cost?
The same as working yourself: drawing is free, and a calculation with the full report costs €1.
Do the whole house in 5 minutes
Trace your floor plan and press Calculate for every room's heat loss, the heat pump size and the radiator check. Free to try, nothing to install, no sign-up.
Open the designer free